• Non-slip Accurate tooth dimension and steel cord ensures minimal stretching, no slippage and constant spends.
• High oil and ozone resistance.
• Special backside surfaces are available. Bando can mold virtually any special configuration on the belt’s backside surface.

Structure

• Polyurethane backing
• Steel cord tensile members (For MXL,Aramid tensile members)
• Polyurethane teeth

• Space saving – High horsepower rating and small pulley requirements permit compact designs.
• Smooth running – Belt runs very smoothly because of ground side wall.
• High speed drive – Because they are very light weight, Banflex belts can be driven at high speeds without excessive vibration or wear.

Banflex Constructions

• Polyurethane
• Polyester tensile members
• Polyurethane compression section.

• Space saving – High horsepower rating and small pulley requirements permit compact designs.
• Smooth running – Belt runs very smoothly because of ground side wall.
• High speed drive – Because they are very light weight, Banflex belts can be driven at high speeds without excessive vibration or wear.

Banflex Constructions

• Polyurethane
• Polyester tensile members
• Polyurethane compression section.

• Space saving – High horsepower rating and small pulley requirements permit compact designs.
• Smooth running – Belt runs very smoothly because of ground side wall.
• High speed drive – Because they are very light weight, Banflex belts can be driven at high speeds without excessive vibration or wear.

Banflex Constructions

• Polyurethane
• Polyester tensile members
• Polyurethane compression section.

Individual V-belts joined with tie bands provide stability and uniform load distribution.

Application
Machinery with pulsating loads (piston pumps, crushers, screens, etc.)
Machinery with shock loads (grinders, crushers, hammer mills, reciprocating saws, chippers, etc.)
Machinery with vertical shaft drives (liquid agitators, centrifuges, mixers, etc.)

Features
Available in Power Ace types and V-Belt types
The tie band permanently bonds multiple belts together to prevent belts from flipping over in the pulley groove on high impact drives
High ratio reduction gear drives can be replaced with flat to V pulley drives for inexpensive, low noise power transmission
Can also be used for conveyance

Line Up:

• High horsepower rating
• Requires about 1/3 of the space needed by traditional Multiple V Belt drive.
• Long life
• High heat and oil resistance
• Length stability. A matched set of Bando Narrow V-Belts for multiple belt drives retains superior uniformity under tension. A Bando matched set remains perfectly matched even after long periods of storage.
• Compared with Conventional V-belt. Bando Narrow V Belts are thick and realized high load.

• High horsepower rating
• Requires about 1/3 of the space needed by traditional Multiple V Belt drive.
• Long life
• High heat and oil resistance
• Length stability. A matched set of Bando Narrow V-Belts for multiple belt drives retains superior uniformity under tension. A Bando matched set remains perfectly matched even after long periods of storage.
• Compared with Conventional V-belt. Bando Narrow V Belts are thick and realized high load.

• High horsepower rating
• Requires about 1/3 of the space needed by traditional Multiple V Belt drive.
• Long life
• High heat and oil resistance
• Length stability. A matched set of Bando Narrow V-Belts for multiple belt drives retains superior uniformity under tension. A Bando matched set remains perfectly matched even after long periods of storage.
• Compared with Conventional V-belt. Bando Narrow V Belts are thick and realized high load.

Higher rate of efficiency (less temperature development)
Increased power transmission capacity
Low space requirements (smaller pulley diameter)
Longer service life (low maintenance)

Product characteristics
Temperature resistant from – 30° to +90°C
Electrically conductive
Limited oil resistance
Highly fire resistant
Particularly resistant to environmental influences like heat, ozone, sunlight and effects of the weather.

Belt construction
Chloroprene impregnated canvas backing
Strong polyester tension members
Neoprene rubber insulation
Fibre reinforced neoprene moulded teeth

Higher rate of efficiency (less temperature development)
Increased power transmission capacity
Low space requirements (smaller pulley diameter)
Longer service life (low maintenance)

Product characteristics
Temperature resistant from – 30° to +90°C
Electrically conductive
Limited oil resistance
Highly fire resistant
Particularly resistant to environmental influences like heat, ozone, sunlight and effects of the weather.

Belt construction
Chloroprene impregnated canvas backing
Strong polyester tension members
Neoprene rubber insulation
Fibre reinforced neoprene moulded teeth